icon Baxi Condensing Gas Boiler Model Nuvola Platinum+ 33 Ga With 40 Liters Methane Or LPG Accumulation Complete With Smoke / LPG Exhaust Kit | CaldaieMurali

Baxi Condensing Gas Boiler Model Nuvola Platinum+ 33 Ga With 40 Liters Methane Or LPG Accumulation Complete With Smoke / LPG Exhaust Kit

Description

ATTENTION THE BOILER IS SUPPLIED WITH METHANE. LPG OPERATION THROUGH ADJUSTMENT BY AN AUTHORIZED SERVICE CENTER. FOR INFO, CONTACT BAXI ASSISTANCE IN ADVANCE

Technical features

  • ErP energy efficiency class (heating and DHW): A
  • Load profile: XL
  • DHW nominal heat input kW 34
  • Heating nominal heat input kW 28.9
  • Sanitary nominal thermal power kW 33
  • Energy efficiency (92/42/EEC) ****
  • Efficiency at 100% Pn (80-60°C): 97.6%
  • Efficiency at 100% Pn (50-30°C): 105.4%
  • Expansion/pre-charge vessel capacity l/bar 7.5/0.8
  • Sanitary water temperature adjustment °C 35-60
  • Boiler capacity 40 l
  • Boiler expansion vessel capacity/pre-charge l/bar 2/3.5
  • Sanitary water production ∆T 25°C l/min 18.9
  • Sanitary water production at discharge ∆T 30°C l/30' 500
  • Degree of protection: IPX5D
  • NOx class (EN 483) 5
  • Dimensions (hxlxp): 950x600x466 mm ; 67.5 kgs
  • Power supply: CNG or LPG

* Operation with LPG through adjustment by the Authorized Service Centre



Cloud Platinum+

Wall mounted gas condensing boilers for heating and DHW production with storage

Total modulation pump

Baxi

The Luna Platinum+ range is renewed with the introduction of a high efficiency electronic pump with permanent magnet motor.

The new fully modulated pump allows, compared to using a pump

Traditional modulating:

  • Lower electricity consumption
  • Better performance
  • Greater durability

Plant deaeration

New electronic "system deaeration" function to facilitate the removal of air during initial ignition.

Efficiency and savings

The objective of a heat generator is to supply the energy necessary to the rooms to maintain conditions of maximum comfort inside them: this means supplying the rooms, through the system, with the same amount of heat that the building loses . In new buildings, the regulations increasingly require greater insulation and consequently less dispersion. Usually there is a tendency to oversize heat generators to favor the production of sanitary water: this leads to an excess of power in heating which, together with the poor modulation capacity of traditional boilers, causes discontinuous functioning and therefore waste of fuel. Discontinuous processes generate energy losses (heat dispersion caused by the pre-washing of the combustion chamber, component wear caused by continuous on-off, decrease in generator efficiency). The modulation system of the Platinum+ range is able to adapt the thermal power produced to the effective power dissipated by the building, avoiding excessive overheating/cooling of the rooms.

Wide modulation range

Baxi

Reduction of on-off cycles

Baxi

The graph shown above highlights the reduction in on/off cycles which distinguishes the new Platinum+ boilers with modulation up to 1:10 compared to a condensing boiler with lower modulation. The reduction of the on/offs determines an improvement in the efficiency of the boiler and consequently a considerable saving for the end user. Standard condensing boilers, on the other hand, with a limited modulation range work at a minimum power level above 6 kW; this allows it to avoid the on/off cycles for only 3% of the period of operation in heating, compromising the performance of the boiler and the life of the components.


GAC: Gas Adaptive Control

The electronics and the gas valve with stepper motor that the new Platinum+ boilers are equipped with guarantee automatic combustion control which is based on:

  • on the flame signal

GAC via the flame signal

Baxi

The system continuously measures the flame signal during boiler operation and adjusts the gas flow rate in order to keep the combustion quality constant and all this without requiring any additional component inside the combustion chamber.

Installers and end users enjoy the following benefits of the GAC:

  • The automatic combustion control favors a reduction in installation times as no manual adjustment of the gas valve or nozzle change is required: in fact, it is sufficient to manually modify some parameters of the electronic board for operation with LPG
  • The boiler self-adapts to the quality of the gas and the length of the flue gas outlets: this means that there are no manual adjustments to make
  • High modulation field 1:10: high efficiency and savings, since such a wide modulation field determines a greater adaptability of the boiler to the thermal dispersions of the building to obtain a higher efficiency and greater durability of the components. The reduction of the on/off cycles, in addition to the greater efficiency, guarantees less noise produced by the boiler
  • Unlike traditional condensing boilers, the boiler always works adjusted to maximum efficiency values ​​favoring a reduction in gas consumption and consequently a lower environmental impact thanks to the control of CO/CO emissions

Power sets

The term Power set identifies the heating power regulation process according to the project data.
The thermal capacity of the boiler, through the Power set device, is adjusted according to the energy requirement: just act on the control panel to adjust some parameters


Complete soundproofing

C structure

Silence is the relative or absolute absence of sound or noise. The noise level of the Luna Platinum+ boiler is comparable to a normal conversation


Digital pressure gauge

The electronic pressure transducer in the hydraulic unit allows you to check the pressure directly on the display. Double alarm level in the event of low pressure: a "warning" level in the event of low pressure in the boiler; a "block" level in the event of a lack of pressure


Intubation solution

For the rehabilitation of flues

Baxi has developed a system that allows easy ducting into existing flues thanks to a Ø50 mm exhaust pipe (for 24kW models).


Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Baxi Condensing Gas Boiler Model Nuvola Platinum+ 33 Ga With 40 Liters Methane Or LPG Accumulation Complete With Smoke / LPG Exhaust Kit

Product form

ATTENTION THE BOILER IS SUPPLIED WITH METHANE. LPG OPERATION THROUGH ADJUSTMENT BY AN AUTHORIZED SERVICE CENTER. FOR INFO, CONTACT BAXI... Read more

€2.200,00 Incl. VAT

    Description

    ATTENTION THE BOILER IS SUPPLIED WITH METHANE. LPG OPERATION THROUGH ADJUSTMENT BY AN AUTHORIZED SERVICE CENTER. FOR INFO, CONTACT BAXI ASSISTANCE IN ADVANCE

    Technical features

    • ErP energy efficiency class (heating and DHW): A
    • Load profile: XL
    • DHW nominal heat input kW 34
    • Heating nominal heat input kW 28.9
    • Sanitary nominal thermal power kW 33
    • Energy efficiency (92/42/EEC) ****
    • Efficiency at 100% Pn (80-60°C): 97.6%
    • Efficiency at 100% Pn (50-30°C): 105.4%
    • Expansion/pre-charge vessel capacity l/bar 7.5/0.8
    • Sanitary water temperature adjustment °C 35-60
    • Boiler capacity 40 l
    • Boiler expansion vessel capacity/pre-charge l/bar 2/3.5
    • Sanitary water production ∆T 25°C l/min 18.9
    • Sanitary water production at discharge ∆T 30°C l/30' 500
    • Degree of protection: IPX5D
    • NOx class (EN 483) 5
    • Dimensions (hxlxp): 950x600x466 mm ; 67.5 kgs
    • Power supply: CNG or LPG

    * Operation with LPG through adjustment by the Authorized Service Centre



    Cloud Platinum+

    Wall mounted gas condensing boilers for heating and DHW production with storage

    Total modulation pump

    Baxi

    The Luna Platinum+ range is renewed with the introduction of a high efficiency electronic pump with permanent magnet motor.

    The new fully modulated pump allows, compared to using a pump

    Traditional modulating:

    • Lower electricity consumption
    • Better performance
    • Greater durability

    Plant deaeration

    New electronic "system deaeration" function to facilitate the removal of air during initial ignition.

    Efficiency and savings

    The objective of a heat generator is to supply the energy necessary to the rooms to maintain conditions of maximum comfort inside them: this means supplying the rooms, through the system, with the same amount of heat that the building loses . In new buildings, the regulations increasingly require greater insulation and consequently less dispersion. Usually there is a tendency to oversize heat generators to favor the production of sanitary water: this leads to an excess of power in heating which, together with the poor modulation capacity of traditional boilers, causes discontinuous functioning and therefore waste of fuel. Discontinuous processes generate energy losses (heat dispersion caused by the pre-washing of the combustion chamber, component wear caused by continuous on-off, decrease in generator efficiency). The modulation system of the Platinum+ range is able to adapt the thermal power produced to the effective power dissipated by the building, avoiding excessive overheating/cooling of the rooms.

    Wide modulation range

    Baxi

    Reduction of on-off cycles

    Baxi

    The graph shown above highlights the reduction in on/off cycles which distinguishes the new Platinum+ boilers with modulation up to 1:10 compared to a condensing boiler with lower modulation. The reduction of the on/offs determines an improvement in the efficiency of the boiler and consequently a considerable saving for the end user. Standard condensing boilers, on the other hand, with a limited modulation range work at a minimum power level above 6 kW; this allows it to avoid the on/off cycles for only 3% of the period of operation in heating, compromising the performance of the boiler and the life of the components.


    GAC: Gas Adaptive Control

    The electronics and the gas valve with stepper motor that the new Platinum+ boilers are equipped with guarantee automatic combustion control which is based on:

    • on the flame signal

    GAC via the flame signal

    Baxi

    The system continuously measures the flame signal during boiler operation and adjusts the gas flow rate in order to keep the combustion quality constant and all this without requiring any additional component inside the combustion chamber.

    Installers and end users enjoy the following benefits of the GAC:

    • The automatic combustion control favors a reduction in installation times as no manual adjustment of the gas valve or nozzle change is required: in fact, it is sufficient to manually modify some parameters of the electronic board for operation with LPG
    • The boiler self-adapts to the quality of the gas and the length of the flue gas outlets: this means that there are no manual adjustments to make
    • High modulation field 1:10: high efficiency and savings, since such a wide modulation field determines a greater adaptability of the boiler to the thermal dispersions of the building to obtain a higher efficiency and greater durability of the components. The reduction of the on/off cycles, in addition to the greater efficiency, guarantees less noise produced by the boiler
    • Unlike traditional condensing boilers, the boiler always works adjusted to maximum efficiency values ​​favoring a reduction in gas consumption and consequently a lower environmental impact thanks to the control of CO/CO emissions

    Power sets

    The term Power set identifies the heating power regulation process according to the project data.
    The thermal capacity of the boiler, through the Power set device, is adjusted according to the energy requirement: just act on the control panel to adjust some parameters


    Complete soundproofing

    C structure

    Silence is the relative or absolute absence of sound or noise. The noise level of the Luna Platinum+ boiler is comparable to a normal conversation


    Digital pressure gauge

    The electronic pressure transducer in the hydraulic unit allows you to check the pressure directly on the display. Double alarm level in the event of low pressure: a "warning" level in the event of low pressure in the boiler; a "block" level in the event of a lack of pressure


    Intubation solution

    For the rehabilitation of flues

    Baxi has developed a system that allows easy ducting into existing flues thanks to a Ø50 mm exhaust pipe (for 24kW models).


    Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
    Data sheetData sheet
    • peso: 35.0 kg
    • classe energetica produzione acs: A
    • classe energetica riscaldamento: A
    • gas: Methane/LPG
    • marca: BAXI
    • metri quadri : 220
    • modello: Nuvola Platinum+ 33 GA
    • potenza in kw: 33
    • potenza nominale: 33
    • superficie riscaldabile mq: 220
    • tipologia : Ad accumulo
    Shipping detailsShipping details

    The order is processed according to the payment method chosen:

    for payments by CREDIT CARD, PAYPAL, MARK, the order is processed the same day. Orders placed before 2.00 pm will be managed on the same day. The BRT or GLS courier will collect the ordered goods from our warehouses the following morning.

    Subsequently, the courier assigns the shipment number (tracking number) and communicates the same to the customer via e-mail, allowing him to follow the delivery status and estimated times in real time on the brt.it or gls-grop.com website. 24-72 the courier will deliver the goods (excluding islands and disadvantaged areas) to the address indicated by the Customer at the time of order confirmation. Transport costs are charged to the customer and are calculated taking into account the volume and/or weight of the ordered item/s. However, product delivery times vary according to the requested item, payment methods and the delivery times chosen by the Customer, which is why the times indicated are merely indicative and cannot be considered binding for Decidiprezzo srl. Orders placed online are delivered throughout Italy, with the exception of Livigno, Campione d'Italia, Vatican City and the Republic of San Marino. In some periods of the year (summer period / Christmas period) the processing times could undergo changes compared to the standard ones declared above.

    NB: In the periods of July and August due to the high amount of orders, delivery times could be delayed

    Icon for coinShipping cost

    Shipping costs vary according to the weight of the order.

    Consult the tables with the weights for Italy and for the smaller islands and disadvantaged areas.

    Warranty detailsWarranty details

    Pursuant to art. 63 of the Consumer Code, the risk of loss and damage to the goods, for reasons not attributable to the seller, is transferred to the consumer when the latter, or a third party designated by him and other than the carrier, physically comes into possession of goods. However, the risk is transferred to the consumer as soon as the goods are delivered to the carrier. The Customer who at the time of purchase has decided to make use of the extra insurance service for the transport of the purchased goods, in the event that he finds anomalies at the time of delivery (packaging damaged or otherwise altered in the closing seals, damaged product or scratched, missing one or more packages ordered), must accept the product by writing on the document provided by the carrier: "WE ACCEPT WITH RESERVE" + description of the anomaly found. In fact, to enforce the insurance coverage it is not sufficient to note "ACCEPTED WITH RESERVE" or "ACCEPTED WITH SUBJECT TO INSPECTION", BUT the reason for the reservation must be explained in detail. If the package or the product should show visible damage, scratches or any other type of anomaly and the courier should refuse to affix a specific reserve, the goods must be refused and the incident reported immediately (and in any case in a timely manner) to the Customer Service of Decidiprice srl. In any case, without prejudice to the seller's obligations in terms of legal guarantee pursuant to articles 128 et seq. of the Consumer Code, Decidiprezzo srl will not be held responsible for any anomalies found in the state of the product, after delivery, if the Customer, in the presence of an anomaly, has accepted the package without making a specific reservation (in the corrected above). Any damage or anomalies must be reported to Customer Service by email to postvendita@climaconvenienza.it. The request must be forwarded no later than 8 calendar days from receipt of the goods. Any notification beyond the aforementioned terms will not be taken into consideration.

    Customer service detailsCustomer service details

    Our customer service department is dedicated to providing support to our customers with any problems or questions they may have before or after purchasing our products.

    Use the direct communication channel to speak to one of our operators, or send us an email to one of the addresses listed on the contact us page.

    Our customer service team is made up of highly trained professionals who are always ready to help customers solve any problem or answer any question quickly and efficiently. We are committed to ensuring maximum customer satisfaction and providing the highest quality after-sales service. So if you need any assistance, don't hesitate to contact us; we will be happy to help you in any way we can.

    Recensioni di CaldaieMurali.it

    Latest Products Viewed

    Login

    Forgot your password?

    Don't have an account yet?
    Create account